QUASAR schematic diagram service manual circuit diagram wiring schema repair instruction guide user manual free pdf download

 

       
       
       
       

 

 

                                                          Search service manual

   
   
   
QUASAR 14 5010 2 1 VCR
QUASAR 3701/14" TV
QUASAR 3702/14" TV
QUASAR B 121 TV
QUASAR B 125 TV
QUASAR B 128 TV
QUASAR CTV 200/2 TEL
QUASAR HQ 801 VCR
QUASAR M 114 TV
QUASAR M 116 TV
QUASAR M 120 TV
QUASAR M 121 TV
QUASAR M 122 TV
QUASAR M 125 TV
QUASAR M 128 TV
QUASAR REM.CONTR.UNIT TEL
QUASAR RING 22 TV
QUASAR S 116 TV
QUASAR S 221 TV
QUASAR S 225 TV
QUASAR S 228 TV
QUASAR S 233 TV
QUASAR S 237 TV
QUASAR SINTONIA TEL
QUASAR SP 225 TV
QUASAR SP 228 TV
QUASAR TVC 99 CH/I TEL

 

     
  QUASAR schematic diagram service manual circuit diagram wiring schema repair instruction guide user manual free pdf download. Service Handbuch Schaltungen Reparaturanleitung Bedienungsanleitungen kostenlos pdf download. Schéma service manual schéma zapojení schémat oprava návod k obsluze návod k použití free pdf ke stažení. Schéma de principe de service manuel Schéma câblage schéma réparation instruction notice manuel téléchargement gratuit pdf. Diagrama esquemático serviço manual do circuito diagrama de fiação esquema reparação instrução guia manual do usuário livre PDF Download. Schema di servizio manuale circuito schema elettrico schema di riparazione di istruzioni guida manuale pdf gratuito scaricare. schemat instrukcja obsługi Schemat okablowania Schemat naprawa instrukcja instrukcja obsługi free pdf pobierz. şeması servis manuel devre şeması kablolama şeması onarım talimat kılavuzu kullanım kılavuzu ücretsiz pdf indir. Schema service manual schema bedrading schema reparatie gebruiksaanwijzing handleiding gratis pdf te downloaden. schematică diagrame de service manualul de circuit diagrama de conexiuni Schema de reparatii de instructiuni Manual de utilizare pe gratis download pdf.  
     
  CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS of this publication. Remember: Safety First.

General Guidance An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line.

Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
 

2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
 

3. Do not spray chemicals on or near this receiver or any of its
assemblies.
 

4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
 

5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
 

6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
 

7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
 

8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.

 

 

 
Copyright © 2007 Tehnomagazin.com
Terms & Conditions                                        Privacy Policy                                                Impressum